EAGLE CUDA 242 MANUAL PDF

No part of this manual may be copied, reproduced, republished, transmitted or distributed for any purpose, without prior written consent of Eagle Electronics. Any unauthorized commercial distribution of this manual is strictly prohibited. Eagle Electronics may find it necessary to change or end our policies, regulations, and special offers at any time. Table of Contents Introduction

Author:Mezibei Vudokus
Country:Sao Tome and Principe
Language:English (Spanish)
Genre:Travel
Published (Last):27 November 2009
Pages:97
PDF File Size:19.90 Mb
ePub File Size:5.12 Mb
ISBN:921-9-41090-442-6
Downloads:51758
Price:Free* [*Free Regsitration Required]
Uploader:Yozshulkis



No part of this manual may be copied, reproduced, republished, transmitted or distributed for any purpose, without prior written consent of Eagle Electronics. Any unauthorized commercial distribution of this manual is strictly prohibited. Eagle Electronics may find it necessary to change or end our policies, regulations, and special offers at any time. Table of Contents Introduction Your unit is a high-quality sonar designed for both professional and novice fishermen.

All Eagle sonars have an automatic mode that finds and displays the bottom, fish, underwater structure and more — right out of the box. All you have to do is press the on PWR key. To get started with your Eagle sonar, first read the installation section. Current drain Back-up memory Built-in memory stores sonar settings when unit is turned off.

Sonar Frequency Operates at boat speeds up to 70 mph 61 kts. Both units operate the same way. The only difference between the two is that the portable unit includes a portable transducer and other items that enable portable use.

Extended storage in temperatures higher or lower than specified will damage the liquid crystal display in your unit. Transducer Installation Preparations The following shows the recommended sequence for installing the transducer: CAUTION: You should read over this entire installation section before drilling any holes in your vehicle or vessel! Determine the approximate location for the sonar unit, so you can plan how and where to route the cables for the transducer and power.

This will help you make sure you have enough cable length for the desired configuration. These are all "kick-up" mounting brackets. They help prevent damage if the transducer strikes an object while the boat is moving. If the transducer does "kick-up," the bracket can easily be pushed back into place without tools. Depending on your sonar unit's connectors, your transducer cable may also have the sonar unit's power cable attached to it. If that is the case, be sure to install the transducer first, before connecting the power cable to a power source.

A sandwich hull also requires polyester resin. Selecting a Transducer Location 1. The location must be in the water at all times, at all operating speeds. The transducer must be placed in a location that has a smooth flow of water at all times. If possible, route the transducer cable away from other wiring on the boat. Electrical noise from engine wiring, bilge pumps and aerators can be displayed on the sonar's screen.

Use caution when routing the transducer cable around these wires. This will help prevent the transducer from entering the boat if it is knocked off at high speed.

Transom Transducer centerline Hull bottom Align transducer centerline with hull bottom. However, there are times when you may need to adjust the transducer slightly higher or lower. The slots in the mounting brackets allow you to loosen the screws and slide the transducer up or down.

If you frequently lose bottom signal lock while running at high speed, the transducer may be coming out of the water as you cross waves or wakes. Move the transducer a little lower to help prevent this. There is no possibility of damage from floating objects. It can't be knocked off when docking or loading on the trailer.

However, the shoot-thru-hull installation does have its drawbacks. First, some loss of sensitivity does occur, even on the best hulls. This varies from hull to hull, even from different installations on the same hull. This is caused by differences in hull lay-up and construction.

Second, the transducer angle cannot be adjusted for the best fish arches. Dot Align plastic ratchets in bracket. Aligning the transducer on the transom. Slide the transducer between the two ratchets. Temporarily slide the bolt though the transducer assembly and hold it against the transom. Looking at the transducer from the side, check to see if it will adjust so that its face is parallel to the ground.

If it does, then the "A" position is correct for your hull. If the transducer's face isn't parallel with the ground, remove the transducer and ratchets from the bracket. Ratchets Insert bolt and check transducer position on transom. Assembling the transducer. Once you determine the correct position for the ratchets, assemble the transducer as shown in the following figure. Don't tighten the lock nut at this time. Drilling mounting holes. Hold the transducer and bracket assembly against the transom.

The transducer's centerline should be in line with the bottom of the hull. Don't let the bracket extend below the hull! Mark the center of each slot for the mounting screw pilot holes. You will drill one hole in the center of each slot. Drill the holes. Use the 29 bit for the 10 screws. Transom Transom Position transducer mount on transom and mark mounting holes. Side view shown at left and seen from above at right.

Attaching transducer to transom. Route cable over bolt and through bracket. Side view shown left and seen from above right. Attach the transducer to the transom.

Slide the transducer up or down until it's aligned properly with the bottom of the hull as shown in the preceding and following figures.

Tighten the bracket's mounting screws, sealing them with the caulking compound. Bottom of hull Deep-"vee" hull Flat-bottom hull Align transducer centerline with hull bottom and attach to transom.

Route the transducer cable through or over the transom to the sonar unit. Make sure you leave some slack in the cable at the transducer. If possible, route the transducer cable away from other wiring. Electrical noise from the engine's wiring, bilge pumps, VHF radio wires, cables and aerators can be picked up by the sonar.

Make a test run to determine the results. If the bottom is lost at high speed, or if noise appears on the display, try sliding the transducer bracket down. This puts the transducer deeper into the water, hopefully below the turbulence causing the noise. Don't allow the transducer bracket to go below the bottom of the hull! Trolling Motor Bracket Installation 1. Attach the optional TMB-S bracket to the transducer as shown in the following figure, using the hardware supplied with the transducer.

Route the transducer cable alongside the trolling motor shaft. Use plastic ties not included to attach the transducer cable to the trolling motor shaft. Make sure there is enough slack in the cable for the motor to turn freely. Route the cable to the sonar unit and the transducer is ready for use. Transducer mounted on trolling motor, side view. Partial fish arches Transducer aimed too far forward Transducer aimed too far back Full fish arch Proper transducer angle Transducer angles and their effects on fish arches.

If the arch slopes up — but not back down — then the front of the transducer is too high and needs to be lowered. If only the back half of the arch is printed, then the nose of the transducer is angled too far down and needs to be raised. NOTE: Periodically wash the transducer's face with soap and water to remove any oil film.

Shoot-Thru-Hull Preparation Hulls with Flotation Materials The transducer installation inside a fiberglass hull must be in an area that does not have air bubbles in the resin or separated fiberglass layers. The sonar signal must pass through solid fiberglass. A successful transducer installation can be made on hulls with flotation materials such as plywood, balsa wood or foam between layers of fiberglass if the material is removed from the chosen area.

See the figure below. Any air bubbles in the fiberglass or the epoxy will reduce or eliminate the sonar signals. Testing Determines Best Location Ideally, the shoot-thru transducer should be installed as close to the transom as possible, close to the centerline. This will give you the best performance during high speed maneuvers. Transducer location high speed Transducer location trolling speed Shoot-thru-hull transducer locations for high speed or trolling speed operation.

KALA SARPA DOSHA TELUGU PDF

Eagle CUDA 242 manual

Go to page of Go. The rules should oblige the seller to give the purchaser an operating instrucion of Eagle CUDA , along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used.

ITEXT ADD BUFFEREDIMAGE TO PDF

Eagle Electronics CUDA 242 User Manual

Many instructions, immediately after the purchase, go into the trash along with the box, which is a mistake. Get acquainted with the information concerning the manual for Eagle CUDA , which will help you to avoid troubles in the future. If you do not want to read brochures every time concerning a Eagle CUDA or other products, it is enough to read them once only - just after buying the device. You will then acquire basic knowledge to maintain Eagle CUDA in good operating condition to make it easily reach the intended life cycle.

Related Articles